TSW-20M Module Project With STM32F303 Microcontroller Series

September 23, 2024

TSW-20M Module Project With STM32F303 Microcontroller Series

متن سربرگ خود را وارد کنید

September 23, 2024

TSW-20M Module Project With STM32F303 Microcontroller Series

What's the purpose of this project?

In this section, we are going to launch the TSW-20M Module using an ARM microcontroller, STM32F series. To use more conveniently and optimally in this project, we use two ready modules GB626EN and GebraBit STM32F303. These two modules contain the minimum necessary elements of the TSW-20M Sensor and the STM32F microcontroller, which are provided by the GebraBit team to facilitate the work.

What are we going to learn in this tutorial?

In this tutorial, in addition to setting up and using the TSW-20M module, you will get to know how to set the various parts of the STM32 microcontroller to set up this sensor using the ADC, how to use the GB626EN module specific library and driver file. You will also learn how to declare functions and finally receive sensor data in the Keil compiler.

What do we need to start this project?

As you probably know, we need some hardware and software to do this project. The titles of these hardware and software are provided to you in the table below and you can prepare/download them by clicking on each of them and get ready to start.

Required hardware	Required software
GEBRABIT TSW-20M Module	Keil compiler
GebraBit STM32F303 module	STM32CubeMX program
ST-LINK/V2 programmer

First as shown in the image below, we connect the GebraBit TSW-20M module to the GebraBit STM32F303 module as follows:

Finally, we will see the value of the TSW-20M module in Real Time in the “Watch1” window of the Keil compiler in the “Debug Session” mode.

STM32CubeMX settings

In the following, we review the settings related to each of the “ADC”, “RCC”, “Debug”, ”GPIO” and “Clock” sections in the STM32F303 microcontroller to develop the GebraBit TSW-20M module.

RCC settings

Due to the presence of “8Mhz” crystal in the GebraBit STM32F303 module, we select the “external clock” in the “RCC” section:

Debug & Programming settings

Regarding the access to “SWCLK” and “SWDIO” pins in the GebraBit STM32F303 module, to reduce the number of pins during “Debug & Programming”, in the “SYS” block, we select the “Serial Wire” option in the “Debug” section:

ADC settings

To get the TSW-20M module output voltage with the GebraBit STM32F303 module enable the ADC in single-ended mode and select PA0 as ADC1_IN1:

GPIO settings

To get the TSW-20M sensor digital output select PA10 pin as GPIO_INPUT. The Gebrabit STM32F303 module has built-in LED and pushbutton in PB6 and PA3 pins so we make the PB6 pin as GPIO_OUTPUT and PA3 pin as GPIO_INPUT to make the cube setting more functional and let you make your ideas into reality with these two modules.

Clock settings

The “clock” settings for each part of the STM32F303 microcontroller in this code, are as follows:

Project Manager settings

“Project Manager” settings are as follows, here we have used “MDK-ARM” version “5.32” compiler:

here we have used the “MDK-ARM” version “5.32” compiler:

After completing all the above settings, we can develop our code easily just by one click on “GENERATE CODE” and adding the TSW_20M library and driver (provided by GebraBit).
You can download the “STM32Cube MX”, “library”, “driver” and KEIL project at the end of this tutorial.

TSW-20M library and driver

In addition to the modular design of various sensors and ICs, GebraBit tries to provide a variety of structured and hardware-independent libraries in C language for the ease of users in setting up and developing software.
For this purpose, after preparing each GebraBit module, the users can refer to the “tutorial” section of the desired module and download the dedicated library, which contains the “ .h” and “ .c” files (Header and Source) and a sample training program under “GebraBit STM32F303”, “GebraBit ATMEGA32A” or “Arduino” development boards.
All the defined functions and structures in the library are commented in full detail and all the received parameters in the arguments of the functions and their return values, are briefly explained. Since the libraries are hardware-independent, the user can easily add the library in any of their favorite compilers and develop it by the desired microcontroller and development board.

GebraBit_TSW_20M.h header file

In this file the casing of the TSW-20M and the configurations related to each of the TSW-20M internal blocks are defined in the form of a “STRUCT” with the name GebraBit_TSW_20M Finally, in the Debug Session environment, all the configurations related to each block can be seen in real time.

TSW_20M struct

All sensor properties and sensor data are defined in this “struct” and all the information and configuration implemented on the sensor are stored in this “structure” and you can see the changes in each part of the sensor in the “Debug Session” environment.

				
					typedef struct TSW_20M
{
            uint8_t                            DIGITAL_VALUE;
            uint32_t                           ADC_RAW_VALUE;
            float                              TURBIDITY;
            float                              ADC_INPUT_VOLTAGE_VALUE;
            ADC_HandleTypeDef                  ADC_HANDELER;
}GebraBit_TSW_20M;

Declaration of functions

At the end of this file, all the functions for receiving data from the module and calibration are declared:

				
					void GB_TSW_20M_Configuration(GebraBit_TSW_20M * TSW_20M);
void GB_TSW_20M_Read_ADC_Value(GebraBit_TSW_20M * TSW_20M);
void GB_TSW_20M_Read_Digital_Value(GebraBit_TSW_20M * TSW_20M);
void GB_TSW_20M_Calculate_Turbidity(GebraBit_TSW_20M * TSW_20M);
void GB_TSW_20M_Get_Data(GebraBit_TSW_20M * TSW_20M);

GebraBit_TSW_20M.c source file

In this file, which is written in C language, all the functions are commented on in full detail, and all the parameters received in the arguments of the functions and their return values are clearly explained so we confine to these explanations and invite users to check this file directly for more information.

Sample program in Keil

After making the Keil project by STM32CubeMX and adding the “GebraBit_TSW_20M.c” library provided by GebraBit, we will examine the “main .c” file of the sample tutorial and view the output of the GebraBit_TSW_20M module in the “watch” part in the Keil compiler “Debugging” environment.

Description of “main.c” file

functions required by the GebraBit TSW-20M module have been added to the structures. In the next part, a variable named TSW_20M_Module of the GebraBit_TSW_20M structure type (this structure is in the GebraBit_TSW_20M header and is explained in the GebraBit_TSW_20M library description section) is defined for the configuration of the GebraBit TSW-20M module:

				
					/* USER CODE BEGIN PTD */
GebraBit_TSW_20M TSW_20M_Module;
/* USER CODE END PTD */

In the next part of the written code, using the GB_TSW_20M_Configuration (&TSW_20M_Module) functions, we set the GebraBit TSW-20M module and finally, in the while part of the program, the data is read from the sensor and Digital Status and ADC values are continuously received:

				
					  /* USER CODE BEGIN 2 */
  GB_TSW_20M_Configuration(&TSW_20M_Module);
  /* USER CODE END 2 */

  /* Infinite loop */
  /* USER CODE BEGIN WHILE */
  while (1)
  {
    /* USER CODE END WHILE */

    /* USER CODE BEGIN 3 */
    GB_TSW_20M_Get_Data(&TSW_20M_Module);
    HAL_Delay(500);
  }

The “main.c” file code text:

				
					/* USER CODE BEGIN Header */
/*
 * ________________________________________________________________________________________________________
 * Copyright (c) 2020 GebraBit Inc. All rights reserved.
 *
 * This software, related documentation and any modifications thereto (collectively �Software�) is subject
 * to GebraBit and its licensors' intellectual property rights under U.S. and international copyright
 * and other intellectual property rights laws. 
 *
 * GebraBit and its licensors retain all intellectual property and proprietary rights in and to the Software
 * and any use, reproduction, disclosure or distribution of the Software without an express license agreement
 * from GebraBit is strictly prohibited.
 
 * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT 
 * NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT IN  
 * NO EVENT SHALL GebraBit BE LIABLE FOR ANY DIRECT, SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, 
 * OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT,
 * NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE
 * OF THE SOFTWARE.
 * ________________________________________________________________________________________________________
 */
/**
  ******************************************************************************
  * @file           : main.c
  * @brief          : Main program body
  * @Author         : Sepehr Azimi
  ******************************************************************************
  * @attention
  *
  * Copyright (c) 2022 STMicroelectronics.
  * All rights reserved.
  *
  * This software is licensed under terms that can be found in the LICENSE file
  * in the root directory of this software component.
  * If no LICENSE file comes with this software, it is provided AS-IS.
  *
  ******************************************************************************
  */
/* USER CODE END Header */
/* Includes ------------------------------------------------------------------*/
#include "main.h"
#include "adc.h"
#include "gpio.h"

/* Private includes ----------------------------------------------------------*/
/* USER CODE BEGIN Includes */
#include "GebraBit_TSW_20M.h"
/* USER CODE END Includes */

/* Private typedef -----------------------------------------------------------*/
/* USER CODE BEGIN PTD */
GebraBit_TSW_20M TSW_20M_Module;
/* USER CODE END PTD */

/* Private define ------------------------------------------------------------*/
/* USER CODE BEGIN PD */
/* USER CODE END PD */

/* Private macro -------------------------------------------------------------*/
/* USER CODE BEGIN PM */

/* USER CODE END PM */

/* Private variables ---------------------------------------------------------*/

/* USER CODE BEGIN PV */

/* USER CODE END PV */

/* Private function prototypes -----------------------------------------------*/
void SystemClock_Config(void);
/* USER CODE BEGIN PFP */

/* USER CODE END PFP */

/* Private user code ---------------------------------------------------------*/
/* USER CODE BEGIN 0 */

/* USER CODE END 0 */

/**
  * @brief  The application entry point.
  * @retval int
  */
int main(void)
{
  /* USER CODE BEGIN 1 */

  /* USER CODE END 1 */

  /* MCU Configuration--------------------------------------------------------*/

  /* Reset of all peripherals, Initializes the Flash interface and the Systick. */
  HAL_Init();

  /* USER CODE BEGIN Init */

  /* USER CODE END Init */

  /* Configure the system clock */
  SystemClock_Config();

  /* USER CODE BEGIN SysInit */

  /* USER CODE END SysInit */

  /* Initialize all configured peripherals */
  MX_GPIO_Init();
  MX_ADC1_Init();
  /* USER CODE BEGIN 2 */
  GB_TSW_20M_Configuration(&TSW_20M_Module);
  /* USER CODE END 2 */

  /* Infinite loop */
  /* USER CODE BEGIN WHILE */
  while (1)
  {
    /* USER CODE END WHILE */

    /* USER CODE BEGIN 3 */
    GB_TSW_20M_Get_Data(&TSW_20M_Module);
    HAL_Delay(500);
  }
  /* USER CODE END 3 */
}

/**
  * @brief System Clock Configuration
  * @retval None
  */
void SystemClock_Config(void)
{
  RCC_OscInitTypeDef RCC_OscInitStruct = {0};
  RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};
  RCC_PeriphCLKInitTypeDef PeriphClkInit = {0};

  /** Initializes the RCC Oscillators according to the specified parameters
  * in the RCC_OscInitTypeDef structure.
  */
  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
  RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS;
  RCC_OscInitStruct.HSEPredivValue = RCC_HSE_PREDIV_DIV1;
  RCC_OscInitStruct.HSIState = RCC_HSI_ON;
  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
  RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
  RCC_OscInitStruct.PLL.PLLMUL = RCC_PLL_MUL2;
  if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
  {
    Error_Handler();
  }

  /** Initializes the CPU, AHB and APB buses clocks
  */
  RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK
                              |RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2;
  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
  RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1;
  RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;

  if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_0) != HAL_OK)
  {
    Error_Handler();
  }
  PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_ADC12;
  PeriphClkInit.Adc12ClockSelection = RCC_ADC12PLLCLK_DIV1;
  if (HAL_RCCEx_PeriphCLKConfig(&PeriphClkInit) != HAL_OK)
  {
    Error_Handler();
  }
}

/* USER CODE BEGIN 4 */

/* USER CODE END 4 */

/**
  * @brief  This function is executed in case of error occurrence.
  * @retval None
  */
void Error_Handler(void)
{
  /* USER CODE BEGIN Error_Handler_Debug */
  /* User can add his own implementation to report the HAL error return state */
  __disable_irq();
  while (1)
  {
  }
  /* USER CODE END Error_Handler_Debug */
}

#ifdef  USE_FULL_ASSERT
/**
  * @brief  Reports the name of the source file and the source line number
  *         where the assert_param error has occurred.
  * @param  file: pointer to the source file name
  * @param  line: assert_param error line source number
  * @retval None
  */
void assert_failed(uint8_t *file, uint32_t line)
{
  /* USER CODE BEGIN 6 */
  /* User can add his own implementation to report the file name and line number,
     ex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */
  /* USER CODE END 6 */
}
#endif /* USE_FULL_ASSERT */

Program output

After generating the Keil project using STM32CubeMX and adding the library, we connect the STLINK V2 programmer to the GebraBit STM32F303 using the STLINKV2 adapter:

STLINKV2 adapter:

By connecting the STLINK V2 programmer to the GebraBit STM32F303, there is no need to apply power to the GebraBit STM32F303 and GebraBit TSW-20M modules, because they receive their supply voltage directly from the STLINK V2 programmer.
Finally, enter the “Debug” mode and by adding the “TSW_20M_Module” to the “watch” window and running the program, we can see the changes in the ADC and Digital Status values of the GebraBit TSW_20M module:

In the following, you can download the “GebraBit TSW-20M module setup project” using the GebraBit STM32F303 module in the Keil environment, the “STM32CubeMX file”, the schematic of the modules, and the “TSW-20M datasheet”.